Other applications that need seal and leak detection, voltage monitoring, three phase monitoring, and other water and wastewater controls. Because submersible pumps are used in of this application, onboard devices for detecting seal failure are required. While we tend to think of water scarcity and contaminated water supplies as third-world issues, water is used, collected, cleaned, and returned to its source before being reused. This is the only sustainable strategy to ensure that water is and is accessible whenever we need it. This emphasizes the necessity and significance of handling and utilizing water. By identifying the issue and its location as soon as possible, Uninterruptible Power Supplies are widely used in wastewater facilities to safeguard crucial process systems from power outages. Only an industrial-grade wide-temperature UPS, on the other hand, is specially built with rugged internal components to work consistently in harsh settings. Wastewater machinery is located both indoors and outdoors, where it is subjected to a variety of climatic obstacles such as temperature extremes, humidity, and wetness. Only an industrial wide-temperature UPS can provide the necessary power security in these harsh environmental circumstances.
Products and Solutions
UNINTERRUPTIBLE POWER SUPPLY (UPS SYSTEMS)
- Power ranges from 0.7 KVA up to 10 KVA (single phased output)
Due to their online double converter technology these UPS systems meet the requirements of the highest protection class VFI-SS-111. During start-up a diagnostic test system is activated verifying the status of the UPS system and the battery. The power related fan control system protects the system against overheating and ensures a long battery life.
- Power ranges 10KVA, 15KVA, 20KVA
UPS systems are available as single-phase or three-phase systems with an output power of 10 kVA, 15 kVA or 20 kVA. The UPS systems of this type can be operated with double converter / continuous transducers technology in online mode (according to VFI-SS-111) or in standby mode to achieve the highest efficiency possible. For redundant operation (half-load parallel operation, n+1 operation) or for performance increase a parallel connection of up to six systems is feasible.
All other ratings and customized UPS are available upon request!
ULTRASONIC TRANSMITTERS SOLUTION
Introducing new range of Ultrasonic Level Products level transmitters provide simple installation and non-contact measurement of liquid level, tank contents, or open channel flow. The transmitters offer IP68 protection and are ideal for enclosed wet wells and sumps. All models have HART for communication with a HART master device such as controller. Installation accessories are also available.
PUMP CONTROL
In drain mode (pump down), the output relay picks up and the LED turns on when liquid reaches the high level probe. The relay drops out and the LED turns off when liquid falls below the low level probe. In fill mode (pump up), the output relay picks up and the LED turns on when liquid falls below the low level probe. The relay drops out and the LED turns off when liquid reaches the high level probe.
SEAL AND LEAK DETECTION
We designed to operate from a 120 VAC supply voltage, detects leaks by either resistive float switch or a pair of conductive probes installed in the seal cavity, while over-temperature is detected by a normally-closed low-temperature switch that is mounted on the stator, with LED’s that indicate green for “normal” and red for “leak” and “over temperature” condition values.
TEMPERATURE SWITCH RELAY
The non-volatile Latching Temperature Switch relay monitors a normally-closed-low temperature switch. It incorporates a bistable relay that retains its state during power failures. LEDs indicate the status of the relay, and connections for an external reset button are provided for manual control. The reset inputs of multiple units may be connected to a single push button if proper polarity is observed when making the connections. Under normal conditions the temperature switch is closed, and the relay is de-energized. When the temperature switch opens, the relay energizes and latches on until the temperature switch re-closes and the reset button is pressed. The unit will function properly with zero to 2k Ω of resistance in series with the temperature switch.
THERMOMETERS
Thermometers are available in a wide variety of configurations for any application. Bimetal thermometers feature, heavy-duty stainless-steel construction for industrial and commercial applications. tridicators and hot water thermometers are a reliable, economical choice for HVAC, plumbing and industrial applications.
THERMOWELLS
Thermowells are protective sheaths used to allow for the safe installation and removal of temperature instruments. Thermowells also protect the instrument against process pressures and are offered in wide variety of materials to resist corrosion.
DIAPHRAGM SEALS
Diaphragm seals are isolation devices which separate pressure gauges and other instruments from the process media while allowing the instrument to measure the process pressure. The service life of the instrument is greatly extended because it is protected from corrosion, clogging, freezing, or pulsation.
DIFFERENTIAL PRESSURE GAUGE
Differential Pressure Gauges measure the difference between two pressures in a system. This comparison allows the user to tell whether the equipment is functioning properly. Diaphragm Type DP Gauges allow no migration of process media from high to low port.
GENERAL SERVICE GAUGES
General Service Gauges offer high repeatability pressure measurement capabilities across a variety of OEM, commercial and industrial applications, including pumps, machinery and related systems, steam boilers or other pressurized vessels, compressors, chemical processing, oil, gas and petrochemical systems, oil and gas pipeline monitoring, power plant equipment, and pulp and paper mills.